l78m00t series no.2609-1/8 features output voltage l78m05t : 5v l78m06t : 6v l78m07t : 7v l78m08t : 8v l78m09t : 9v l78m10t : 10v l78m12t : 12v l78m15t : 15v l78m18t : 18v l78m20t : 20v l78m24t : 24v 500ma output. on-chip thermal protector. on-chip overcurrent limiter. on-chip aso protector. small-sized power package tp-3h permitting the equipment to be made compact. the allowable power dissipation can be increased by being surface-mounted on the board. capable of being mounted in a variety of methods because of various lead forming versions available. specifications [common to l78m00t series] maximum ratings at ta=25 c parameter symbol conditions ratings unit maximum supply voltage v cc max pin 1 35 v allowable power dissipation pd max no fin 1.0 w operating temperature topr --20 to +80 c storage temperature tstg --40 to +150 c sanyo electric co.,ltd. semiconductor company tokyo office tokyo bldg., 1-10, 1 chome, ueno, taito-ku, tokyo, 110-8534 japan 21006 sy im / d1599th (kt) / d0694hk / 9237ki / 9107ta, ts any and all sanyo products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. consult with your sanyo representative nearest you before using any sanyo products described or contained herein in such applications. sanyo assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all sanyo products described or contained herein. l78m00t series monolithic linear ic 5 to 24v 0.5a 3-pin voltage regulators ordering number : en2609c
l78m00t series no.2609-2/8 [l78m05t] recommended operating conditions at ta=25 c parameter symbol conditions ratings unit input voltage v in 7.5 to 20.0 v output current i out 5 to 500 ma operating characteristics at ta=25 c, v in =10v, i out =350ma, see specified test circuit. ratings parameter symbol conditions min typ max unit output voltage v out tj=25 c 4.8 5.0 5.2 v line regulation v o iine tj=25 c, 7v v in 25v, i out =200ma 3.0 50 mv tj=25 c, 8v v in 20v, i out =200ma 1.0 25 mv load regulation v o ioad tj=25 c, 5ma i out 500ma 100 mv tj=25 c, 5ma i out 200ma 50 mv output voltage v out 7v v in 20v, 5ma i out 350ma 4.75 5.25 v current dissipation i cc tj=25 c 4.5 6.0 ma current dissipation variation (line) i cc iine 8v v in 20v, i out =200ma 0.8 ma current dissipation variation (load) i cc ioad 5ma i out 350ma 0.5 ma output noise voltage v no 10hz f 100khz 40 v ripple rejection rrej f=120hz, 8v v in 19v, tj=25 c, i out =100ma 62 db f=120hz, 8v v in 19v, tj=25 c, i out =300ma 62 80 db minimum input-output voltage dropout vdrop i out =350ma 2.0 v short current i os tj=25 c, v in =35v, to gnd 300 ma peak output current i op tj=25 c 0.7 a [l78m06t] recommended operating conditions at ta=25 c parameter symbol conditions ratings unit input voltage v in 8.5 to 21 v output current i out 5 to 500 ma operating characteristics at ta=25 c, v in =11v, i out =350ma, see specified test circuit. ratings parameter symbol conditions min typ max unit output voltage v out tj=25 c 5.75 6.0 6.25 v line regulation v o iine tj=25 c, 8v v in 25v, i out =200ma 5.0 60 mv tj=25 c, 9v v in 20v, i out =200ma 1.5 30 mv load regulation v o ioad tj=25 c, 5ma i out 500ma 120 mv tj=25 c, 5ma i out 200ma 60 mv output voltage v out 8v v in 21v, 5ma i out 350ma 5.7 6.3 v current dissipation i cc tj=25 c 4.5 6.0 ma current dissipation variation (line) i cc iine 9v v in 25v, i out =200ma 0.8 ma current dissipation variation (load) i cc ioad 5ma i out 350ma 0.5 ma output noise voltage v no 10hz f 100khz 45 v ripple rejection rrej f=120hz, 9v v in 20v, tj=25 c, i out =100ma 59 db f=120hz, 9v v in 20v, tj=25 c, i out =300ma 59 80 db minimum input-output voltage dropout vdrop i out =350ma 2.0 v short current i os tj=25 c, v in =35v, to gnd 300 ma peak output current i op tj=25 c 0.7 a
l78m00t series no.2609-3/8 [l78m07t] recommended operating conditions at ta=25 c parameter symbol conditions ratings unit input voltage v in 9.5 to 22 v output current i out 5 to 500 ma operating characteristics at ta=25 c, v in =12v, i out =350ma, see specified test circuit. ratings parameter symbol conditions min typ max unit output voltage v out tj=25 c 6.72 7.0 7.28 v line regulation v o iine tj=25 c, 9v v in 25v, i out =200ma 6.0 60 mv tj=25 c, 10v v in 20v, i out =200ma 2.0 30 mv load regulation v o ioad tj=25 c, 5ma i out 500ma 140 mv tj=25 c, 5ma i out 200ma 70 mv output voltage v out 9v v in 22v, 5ma i out 350ma 6.6 7.4 v current dissipation i cc tj=25 c 4.6 6.0 ma current dissipation variation (line) i cc iine 10v v in 25v, i out =200ma 0.8 ma current dissipation variation (load) i cc ioad 5ma i out 350ma 0.5 ma output noise voltage v no 10hz f 100khz 48 v ripple rejection rrej f=120hz, 10v v in 21v, tj=25 c, i out =100ma 58 db f=120hz, 10v v in 21v, tj=25 c, i out =300ma 58 80 db minimum input-output voltage dropout vdrop i out =350ma 2.0 v short current i os tj=25 c, v in =35v, to gnd 300 ma peak output current i op tj=25 c 0.7 a [l78m08t] recommended operating conditions at ta=25 c parameter symbol conditions ratings unit input voltage v in 10.5 to 23 v output current i out 5 to 500 ma operating characteristics at ta=25 c, v in =15v, i out =350ma, see specified test circuit. ratings parameter symbol conditions min typ max unit output voltage v out tj=25 c 7.7 8.0 8.3 v line regulation v o iine tj=25 c, 10.5v v in 25v, i out =200ma 6.0 60 mv tj=25 c, 11v v in 20v, i out =200ma 2.0 30 mv load regulation v o ioad tj=25 c, 5ma i out 500ma 160 mv tj=25 c, 5ma i out 200ma 80 mv output voltage v out 10.5v v in 23v, 5ma i out 350ma 7.6 8.4 v current dissipation i cc tj=25 c 4.6 6.0 ma current dissipation variation (line) i cc iine 11v v in 25v, i out =200ma 0.8 ma current dissipation variation (load) i cc ioad 5ma i out 350ma 0.5 ma output noise voltage v no 10hz f 100khz 50 v ripple rejection rrej f=120hz, 11.5v v in 22v, tj=25 c, i out =100ma 56 db f=120hz, 11.5v v in 22v, tj=25 c, i out =300ma 56 80 db minimum input-output voltage dropout vdrop i out =350ma 2.0 v short current i os tj=25 c, v in =35v, to gnd 300 ma peak output current i op tj=25 c 0.7 a
l78m00t series no.2609-4/8 [l78m09t] recommended operating conditions at ta=25 c parameter symbol conditions ratings unit input voltage v in 12 to 25 v output current i out 5 to 500 ma operating characteristics at ta=25 c, v in =16v, i out =350ma, see specified test circuit. ratings parameter symbol conditions min typ max unit output voltage v out tj=25 c 8.6 9.0 9.4 v line regulation v o iine tj=25 c, 11.5v v in 25v, i out =200ma 6.0 100 mv tj=25 c, 12v v in 20v, i out =200ma 2.0 50 mv load regulation v o ioad tj=25 c, 5ma i out 500ma 180 mv tj=25 c, 5ma i out 200ma 90 mv output voltage v out 11.5v v in 24v, 5ma i out 350ma 8.5 9.5 v current dissipation i cc tj=25 c 4.6 6.0 ma current dissipation variation (line) i cc iine 12.5v v in 25v, i out =200ma 0.8 ma current dissipation variation (load) i cc ioad 5ma i out 350ma 0.5 ma output noise voltage v no 10hz f 100khz 60 v ripple rejection rrej f=120hz, 12v v in 23v, tj=25 c, i out =100ma 56 db f=120hz, 12v v in 23v, tj=25 c, i out =300ma 56 80 db minimum input-output voltage dropout vdrop i out =350ma 2.0 v short current i os tj=25 c, v in =35v, to gnd 300 ma peak output current i op tj=25 c 0.7 a [l78m10t] recommended operating conditions at ta=25 c parameter symbol conditions ratings unit input voltage v in 13 to 25 v output current i out 5 to 500 ma operating characteristics at ta=25 c, v in =17v, i out =350ma, see specified test circuit. ratings parameter symbol conditions min typ max unit output voltage v out tj=25 c 9.6 10.0 10.4 v line regulation v o iine tj=25 c, 12.5v v in 25v, i out =200ma 7.0 100 mv tj=25 c, 13v v in 22v, i out =200ma 2.0 50 mv load regulation v o ioad tj=25 c, 5ma i out 500ma 200 mv tj=25 c, 5ma i out 200ma 100 mv output voltage v out 12.5v v in 25v, 5ma i out 350ma 9.5 10.5 v current dissipation i cc tj=25 c 4.6 6.0 ma current dissipation variation (line) i cc iine 13.5v v in 25v, i out =200ma 0.8 ma current dissipation variation (load) i cc ioad 5ma i out 350ma 0.5 ma output noise voltage v no 10hz f 100khz 65 v ripple rejection rrej f=120hz, 13v v in 25v, tj=25 c, i out =100ma 55 db f=120hz, 13v v in 25v, tj=25 c, i out =300ma 55 80 db minimum input-output voltage dropout vdrop i out =350ma 2.0 v short current i os tj=25 c, v in =35v, to gnd 300 ma peak output current i op tj=25 c 0.7 a
l78m00t series no.2609-5/8 [l78m12t] recommended operating conditions at ta=25 c parameter symbol conditions ratings unit input voltage v in 15 to 25 v output current i out 5 to 500 ma operating characteristics at ta=25 c, v in =19v, i out =350ma, see specified test circuit. ratings parameter symbol conditions min typ max unit output voltage v out tj=25 c 11.5 12.0 12.5 v line regulation v o iine tj=25 c, 14.5v v in 30v, i out =200ma 8.0 100 mv tj=25 c, 16v v in 25v, i out =200ma 2.0 50 mv load regulation v o ioad tj=25 c, 5ma i out 500ma 240 mv tj=25 c, 5ma i out 200ma 120 mv output voltage v out 14.5v v in 27v, 5ma i out 350ma 11.4 12.6 v current dissipation i cc tj=25 c 4.8 6.0 ma current dissipation variation (line) i cc iine 15v v in 30v, i out =200ma 0.8 ma current dissipation variation (load) i cc ioad 5ma i out 350ma 0.5 ma output noise voltage v no 10hz f 100khz 75 v ripple rejection rrej f=120hz, 15v v in 25v, tj=25 c, i out =100ma 55 db f=120hz, 15v v in 25v, tj=25 c, i out =300ma 55 80 db minimum input-output voltage dropout vdrop i out =350ma 2.0 v short current i os tj=25 c, v in =35v, to gnd 300 ma peak output current i op tj=25 c 0.7 a [l78m15t] recommended operating conditions at ta=25 c parameter symbol conditions ratings unit input voltage v in 18 to 30 v output current i out 5 to 500 ma operating characteristics at ta=25 c, v in =23v, i out =350ma, see specified test circuit. ratings parameter symbol conditions min typ max unit output voltage v out tj=25 c 14.4 15.0 15.6 v line regulation v o iine tj=25 c, 17.5v v in 30v, i out =200ma 10.0 100 mv tj=25 c, 19v v in 30v, i out =200ma 3.0 50 mv load regulation v o ioad tj=25 c, 5ma i out 500ma 300 mv tj=25 c, 5ma i out 200ma 150 mv output voltage v out 17.5v v in 30v, 5ma i out 350ma 14.25 15.75 v current dissipation i cc tj=25 c 4.8 6.0 ma current dissipation variation (line) i cc iine 17.5v v in 30v, i out =200ma 0.8 ma current dissipation variation (load) i cc ioad 5ma i out 350ma 0.5 ma output noise voltage v no 10hz f 100khz 90 v ripple rejection rrej f=120hz, 18.5v v in 28.5v, tj=25 c, i out =100ma 54 db f=120hz, 18.5v v in 28.5v, tj=25 c, i out =300ma 54 70 db minimum input-output voltage dropout vdrop i out =350ma 2.0 v short current i os tj=25 c, v in =35v, to gnd 300 ma peak output current i op tj=25 c 0.7 a
l78m00t series no.2609-6/8 [l78m18t] recommended operating conditions at ta=25 c parameter symbol conditions ratings unit input voltage v in 21 to 33 v output current i out 5 to 500 ma operating characteristics at ta=25 c, v in =27v, i out =350ma, see specified test circuit. ratings parameter symbol conditions min typ max unit output voltage v out tj=25 c 17.3 18.0 18.7 v line regulation v o iine tj=25 c, 21v v in 35v, i out =200ma 10.0 100 mv tj=25 c, 22v v in 35v, i out =200ma 5.0 50 mv load regulation v o ioad tj=25 c, 5ma i out 500ma 360 mv tj=25 c, 5ma i out 200ma 180 mv output voltage v out 21v v in 33v, 5ma i out 350ma 17.1 18.9 v current dissipation i cc tj=25 c 4.9 6.0 ma current dissipation variation (line) i cc iine 21v v in 33v, i out =200ma 0.8 ma current dissipation variation (load) i cc ioad 5ma i out 350ma 0.5 ma output noise voltage v no 10hz f 100khz 100 v ripple rejection rrej f=120hz, 22v v in 33v, tj=25 c, i out =100ma 53 db f=120hz, 22v v in 33v, tj=25 c, i out =300ma 53 70 db minimum input-output voltage dropout vdrop i out =350ma 2.0 v short current i os tj=25 c, v in =35v, to gnd 300 ma peak output current i op tj=25 c 0.7 a [l78m20t] recommended operating conditions at ta=25 c parameter symbol conditions ratings unit input voltage v in 23 to 35 v output current i out 5 to 500 ma operating characteristics at ta=25 c, v in =29v, i out =350ma, see specified test circuit. ratings parameter symbol conditions min typ max unit output voltage v out tj=25 c 19.2 20.0 20.8 v line regulation v o iine tj=25 c, 23v v in 35v, i out =200ma 10.0 100 mv tj=25 c, 24v v in 35v, i out =200ma 5.0 50 mv load regulation v o ioad tj=25 c, 5ma i out 500ma 400 mv tj=25 c, 5ma i out 200ma 200 mv output voltage v out 23v v in 35v, 5ma i out 350ma 19.0 21.0 v current dissipation i cc tj=25 c 4.9 6.0 ma current dissipation variation (line) i cc iine 23v v in 35v, i out =200ma 0.8 ma current dissipation variation (load) i cc ioad 5ma i out 350ma 0.5 ma output noise voltage v no 10hz f 100khz 110 v ripple rejection rrej f=120hz, 24v v in 34v, tj=25 c, i out =100ma 53 db f=120hz, 24v v in 34v, tj=25 c, i out =300ma 53 70 db minimum input-output voltage dropout vdrop i out =350ma 2.0 v short current i os tj=25 c, v in =35v, to gnd 300 ma peak output current i op tj=25 c 0.7 a
l78m00t series no.2609-7/8 [l78m24t] recommended operating conditions at ta=25 c parameter symbol conditions ratings unit input voltage v in 27 to 35 v output current i out 5 to 500 ma operating characteristics at ta=25 c, v in =33v, i out =350ma, see specified test circuit. ratings parameter symbol conditions min typ max unit output voltage v out tj=25 c 23.0 24.0 25.0 v line regulation v o iine tj=25 c, 27v v in 35v, i out =200ma 10.0 100 mv tj=25 c, 28v v in 35v, i out =200ma 5.0 50 mv load regulation v o ioad tj=25 c, 5ma i out 500ma 480 mv tj=25 c, 5ma i out 200ma 240 mv output voltage v out 27v v in 35v, 5ma i out 350ma 22.8 25.2 v current dissipation i cc tj=25 c 5.0 6.0 ma current dissipation variation (line) i cc iine 27v v in 35v, i out =200ma 0.8 ma current dissipation variation (load) i cc ioad 5ma i out 350ma 0.5 ma output noise voltage v no 10hz f 100khz 170 v ripple rejection rrej f=120hz, 28v v in 35v, tj=25 c, i out =100ma 50 db f=120hz, 28v v in 35v, tj=25 c, i out =300ma 50 70 db minimum input-output voltage dropout vdrop i out =350ma 2.0 v short current i os tj=25 c, v in =35v, to gnd 300 ma peak output current i op tj=25 c 0.7 a package dimensions equivalent circuit unit : mm 3110a specified test circuit (common to l78m00t series) 6.5 5.0 123 7.0 1.5 7.5 (5.5) 0.5 2.6 (0.65) 1.2 0.5 0.5 2.3 0.6 sanyo : tp3h input gnd output overcurrent limiter starter aso protector thermal protector error amp reference voltage il00021 1 2 3 input 0.33 f 0.1 f output l78moot series il00022 3 1 2
l78m00t series no.2609-8/8 specifications of any and all sanyo products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer?s products or equipment. to verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer?s products or equipment. sanyo electric co., ltd. strives to supply high-quality high-reliability products. however, any and all semiconductor products fail with some probability. it is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. when designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. in the event that any or all sanyo products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of sanyo electric co. , ltd. any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. when designing equipment, refer to the "delivery specification" for the sanyo product that you intend to use. information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. sanyo believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. this catalog provides information as of february, 2006. specifications and information herein are subject to change without notice. ps the allowable power dissipation (pd max) is 1.0w (ta=25 c) with no fin attached. when the l78m00t series are surface-mounted on a hybrid ic board or printed circuit board, a high allowable power dissipation can be obtained, though they are placed in a small-sized package. shown below is the relationship between the cu-foiled area and the allowable power dissipation when the l78m00t series are surface-mounted on a glass epoxy board (50 ? 50 ? 0.8mm 3 ). lead formings fa formings lr formings pd max -- ta allowable power dissipation, pd max -- w ambient temperature, ta -- c 1.2 1.0 0.8 0.6 0.2 0.4 0 --20 0 40 20 60 80 100 2 7 5 3 2 1.0 10 5 7 22 2 357 1000 3 il00023 pd max -- s allowable power dissipation, pd max -- w cu-foiled area, s -- mm 2 il00024 no heat sink 357 100 surface-mounted on board 50 ? 50 ? 0.8tmm 3 (glass epoxy) il00025 il00026
|
